Audio Technica ATW-1662 Specifications download pdf (Page 4)

B. Select Open Frequency Scan Function

1. From the normal operating mode, press and hold the set

button until display flashes.

2. To select scan function, press and hold CH SELECT/SCAN

button, continue to hold until available frequency is

automatically displayed.

3. (a) To select frequency, press and hold SET button until

display stops flashing.

(b) To cancel frequency selection, simply press the SET

button once. The receiver then returns to the normal

operation without making any changes.

Figure D

Front Panel Controls and Functions (Figure. B)

1. POWER SWITCH/INDICATOR: Press switch on, and the

"Power" indicator will light.

2. LCD WINDOW: Liquid Crystal Display indicates control

settings and operational readings. See Figure D for

examples.

3. TUNER OPERATION INDICATOR: Indicates which Tuner

(A or B) has the better reception and is in operation.

4. SET BUTTON: Activates access to Frequency/Scan

mode and sets or cancels selected function when used in

combination with CH SELECT/SCAN button (Item 5).5.

5. CH SELECT/SCAN BUTTON: Use in conjunction

with the SET button (Item 4) to select operation frequency

and scan function.

Figure B

Receiver Controls and Functions

6. AF LEVEL CONTROL: Adjusts audio output level of both AF

Output jacks; maximum output is fully clockwise.

7. SQUELCH CONTROL: Adjusts level of noise-muting circuit

(preset at factory but can be adjusted as circumstances

warrant).

8. MOUNTING ADAPTERS: For mounting the receiver in any

standard 19" rack. Attach adapters to the receiver with the

screws supplied and remove the four receiver feet. (Use

optional AT8616 joining-plate kit to mount two ATW-R160

receivers side-by-side.)

9. PLL Lock indicator: This indicates Phased Lock Loop

frequency controlled oscillator has locked displayed

frequency.

Rear Panel Controls and Functions (Figure C)

10. ANTENNA INPUT JACK: BNC-type antenna connector for

Tuner “B.” Attach the antenna directly, or extend it with a

low-loss antenna cable. See the “Antennas” section on

page 3 for more details.

11. ANTENNA INPUT JACK: Input for Tuner “A.” Attach the

antenna directly, or extend it with a low-loss antenna cable.

12. GROUND LIFT SWITCH: Disconnects the ground pin of the

balanced output jack (12) from ground. Normally, the switch

should be to the left (ground connected). If hum caused by

a ground loop occurs, slide switch to the right (ground

lifted).

13. BALANCED AUDIO OUTPUT JACK: XLRM-type connector.

A standard 2-conductor shielded cable can be used to

connect the receiver output to a balanced microphone-level

input on a mixer or integrated amplifier.

14. UNBALANCED AUDIO OUTPUT JACK:

" phone jack. Can

be connected to an unbalanced aux-level input of a mixer,

guitar amp or tape recorder.

15. POWER INPUT JACK: Connect the DC plug from the

included AC adapter.

16. ATW-RA1 Rack-Mount Antenna kit mounting Holes: Mount

optional front-mount antenna kit ATW-RA1 on these holes.

Power On/Off

To turn the receiver on, press the Power switch. The Power

light and the LCD window will come on after about 1-2

seconds. The operating channel number and frequency will be

displayed in the window after the power-up sequence. To turn

the receiver off, press the Power switch again.

How to Make Setting Changes

A. Select Frequency Manually

1. From the normal operating mode, press and hold the set

button until display flashes.

2. To select frequency, press CH SELECT/SCAN button once

at a time until desired channel is displayed (1 to 9, A to F).

3. (a) To select frequency, press and hold SET button until

display stops flashing.

(b) To cancel frequency selection, simply press the SET

button once. The receiver then returns to the normal

operation.

CHANNEL

840.125

MHZ

ANT A ANT B

67 8

10 11

Figure c

1 2 3 4 5 6 7 8 9 ... 15 16

Comments to this Manuals

No comments

Audio Technica ATW-1662 Specifications Page 4

Comments to this Manuals

Related products and manuals for Microphones Audio Technica ATW-1662