Audio-technica AEW-T1000A User Manual download pdf (Page 8)

Artist Elite

4000 & 5000 Series Professional UHF Wireless Systems

LINKS

OUT (N/A)

AEW-R5200

AEW-R4100

MASTER SLV 1

SLV 2 SLV 3

SLV 4 SLV 5

SLV 6

OUT

POWER

OFF

MODE/SET

OUTPUT

PHONES

UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R5200

MIN MAX

PUSH SEL

LEVEL

RX NAME

POWER

OFF

MODE/SET

OUTPUT

PHONES

UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R5200

MIN MAX

PUSH SEL

LEVEL

RX NAME

POWER

OFF

MODE/SET

OUTPUT

PHONES

UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R5200

MIN MAX

PUSH SEL

LEVEL

RX NAME

UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R4100

ALERT

MODE/SET

POWER

OFF

PHONES

MIN–

LEVEL

–MAX

RX NAME

AEW-R4100 SLV 7

OUT

UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R4100

ALERT

MODE/SET

POWER

OFF

PHONES

MIN–

LEVEL

–MAX

RX NAME

not harm the internal 12V supply, make certain that an antenna cable

shield does not contact the center conductor. Antenna Power (“ANT.

PWR”) is selected (switched on or off) from the LCD menu. (On the

AEW-R5200, Antenna Power will be found in the menu on Channel

1 only.)

Front-mount Antennas

AEW-R4100: Provision has been made to move the antenna jacks

from the rear to the front of the receiver. However, because this

involves opening the receiver case and exposing AC power circuitry,

instructions are not included in this manual. A qualified service

technician must perform this modification.

AEW-R5200: BNC-to-BNC connectors and jumper cables are included

with the unit to permit mounting antennas on the front panel.

• BNC-BNC through-panel connectors: Remove the nut and

lock-washer from each connector. Install the connectors from

the front into the two panel holes. Note that the flat on the

threaded section must be aligned with the flat in each panel

hole. Secure each connector from the back with its lock-

washer and nut, tightening the nut firmly.

• BNC-BNC cable jumpers: Connect the jumpers to the rear

antenna jacks first; then attach them to the BNC connectors on

the front panel. Make certain the bayonet twist-rings are fully

latched on the connectors at both ends.

AEW-R5200: Press and release the Phones Level control knob to

switch headphone monitoring from Channel 1 to Channel 2 and

back again. Small, lighted indicators just above the knob show which

receiver channel is being monitored.

Power Connections

The switching power supply is designed to operate properly from

any AC power source 100–240V, 50/60 Hz without user adjustment.

Simply connect the receiver to a standard AC power outlet, using

only an IEC-type input cordset approved for the country of use.

Power to the unit is controlled by the front-panel Power switch.

AEW-R5200: An auxiliary AC “jumper” (pass-through) outlet is

provided on the rear panel, and a ”jumper” power cordset is included,

to simplify power connections by “daisy-chaining” an array of AEW-

R5200’s. Maximum output from the auxiliary outlet is 5 Amperes,

which will easily handle a full complement of AEW-R5200 units.

“Link” Connections

Artist Elite Series multi-channel systems can comprise all AEW-R4100,

all AEW-R5200, or combinations of AEW-R4100 and AEW-R5200

receivers. The exclusive IntelliScan™ channel assignment system

provides easy, automatic scanning of the RF spectrum and assignment

of usable, compatible frequencies to all linked AEW receiver channels.

Both AEW receiver models can be interconnected using Link In/Out

jacks and included link cables. In addition, the AEW-R5200 offers a

built-in Ethernet 10 BaseT connection, with interface software provided

on CD-ROM. See the separate AEW Control Interface manual provided

with AEW-R5200 receivers and 5000 Series systems.

All AEW receivers in a linked multi-channel system should be

interconnected with included link cables. When the system is

properly configured, the “slave” units will “link data in” to the

“Master” unit. (See Figure B for an example.)

1. First, decide which receiver will be the “Master” unit. Connect

a link cable to the Link In jack only. (In an AEW-R5200, the

Channel 1 unit is the Master and Channel 2 becomes the first

“slave.”)

2. Connect the free end of the link cable from the Master unit (in

#1 above) to the Link Out jack of the desired “next” unit.

3. Connect one end of a new link cable to the Link In jack of the

unit in #2 above.

4. Connect the free end of the link cable from the unit in #2

above to the Link Out jack of the desired “next” unit.

5. Continue this process of “daisy-chaining” the system’s

receivers together with link cables. The “last” unit in the

system will have a cable connected to its Link Out jack, but no

connection to its Link In jack.

Installing link cables starting with the last slave unit and working

toward the Master unit is also acceptable practice.

The attachment order of link cables establishes the numerical order

of the receivers in the multi-channel system, from the selected

Master unit through all the slave units. (In the case of AEW-R5200

receivers, a unit’s Channel 1 always comes before its Channel 2.)

In a multi-channel system that includes both models of receivers,

it’s common practice to position all the AEW-R5200 units first in the

chain; followed by any AEW-R4100 units.

Note 1: For the receiver linking to work, all receivers in the system

must have AC power applied at the same time, or the Master

receiver must be turned on last.

Note 2: In addition, if AC power is interrupted or a link connection

is broken at any receiver in a linked system, even for an instant,

receivers from that unit onward are no longer linked to the system.

When all power and linking have been restored, the system must

be restarted by turning all the receivers Off, then On (all turned on

simultaneously, or the Master receiver must be turned on last). This

will re-initialize the system and re-establish all the data links.

Fig. B

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Comments to this Manuals

No comments

Audio-technica AEW-T1000A User Manual Page 8

Comments to this Manuals

Related products and manuals for Audio accessories Audio-technica AEW-T1000A