Audio Technica ATW-701P Specifications download pdf (Page 5)

ransmitter Setup, Controls And Functions

Figure F-UniPak

Transmitter Top View

Figure G-Handheld

Transmitter Bottom

View

Input Connector

ower Switch

Power/Mute/

Battery Indicator

Antenna

Power Switch

ower/Mute/Battery Indicator

After the battery is installed, press and hold the power button

until the battery indicator LED turns green (Fig. F & G). (It will

turn red first; keep holding until it turns green). If the battery

indicator LED does not light up when the power button is

ressed, the batteries are installed incorrectly or they are dead.

The LED will flash to indicate low-battery condition.

Mute Function

With the transmitter on, a slight touch of the Power/Mute

button will toggle between muted and unmuted operation.

Red LED indicates muted operation. Green LED indicates

unmuted operation.

UniPak

Transmitter Input Connection

Connect an audio input device (microphone or guitar cable) to

the audio input connector on the top of the transmitter. A

number of Audio-Technica professional microphones and cables

are available separately, pre-terminated with a UniPak

input

connector (see www.audio-technica.com.)

UniPak

Transmitter Antenna

he UniPak

ransmitter includes a permanently-attached

flexible antenna. For best results, allow the antenna to hang

freely and full length from the transmitter. If the received signal

is marginal, experiment with different transmitter positions on

your body or instrument; or try repositioning the receiver. Do

not attempt to remove, replace or change the length of the

transmitting antenna.

System Operation

Plug in the receiver.

Receiver On…

The LED display will light up. If either A or B diversity indicators

lights up at this point (without transmitter on) there may be

interference in the area. If this occurs, change the operating

channel.

How to Make Operating Channel Changes

Operating channel changes (frequency changes) may be made in

two ways: manually and automatically.

To change channel manually

Press the Select button repeatedly until desired channel is

reached. Press and hold the Set/Scan button to manually set the

receiver to indicated channel. Channel number will stop

flashing. (A brief touch of the Set/Scan button will revert to

previously set channel). If the Set button is not pressed within

10 seconds to confirm the selection, the system will revert to its

original channel.

To change channel automatically

Press and hold the Set/Scan button for about two seconds. The

current channel will flash three times quickly; then the system

will begin to scan for the next open channel. When it finds an

open channel, it will flash the open channel three times and

then set the channel. (If an open channel is not found, the

automatic scan will return to the original channel and flash 5

times.)

Transmitter On…

Before turning on the transmitter, use the provided screwdriver

to set the transmitter channel selector switches (Fig. D on page

4 and Fig. H on page 6) to the same number that is displayed

on the receiver. Select channels 1-8 (channels 9 and 0 are for

service use). The transmitter may be either on or off when

changing channels (frequencies). When changing channels with

the transmitter on and unmuted, the LED will turn red as the

adjustment is being made; it will turn green when the channel

is set. (When changing channels with the transmitter on and

muted, the LED will remain red during and after channel

adjustment, as long as the transmitter is muted; when the

transmitter is unmuted, the LED will turn green.)

The transmitters have a soft-touch Power Switch. When the

transmitter is “on,” the transmitter produces both RF and audio.

When the transmitter is switched on and in normal operation,

the receiver's diversity indicators will display which antenna is

active.

Setting Levels

Correct adjustment of transmitter audio input, receiver audio

output, and mixer/amplifier input and output levels is important

for optimum system performance.

ATW-T702 HandheldTransmitter

The 700 Series handheld transmitter trim (volume) control

(Fig. H on page 6) has factory pre-set audio input levels. Factory

setting is full clockwise, maximum gain.

Set the receiver's AF Level control to its full clockwise position

(maximum). (Fig. C on page 4).

While speaking/singing into the microphone at typically loud

levels, check the AF peak indicator on the receiver. If the AF

peak indicator is easily illuminated and distortion is heard

through the system, it may be necessary to adjust the transmitter

audio input level.

To adjust the transmitter audio input level, unscrew the lower

body cover and slide it downwards, exposing the screwdriver

and trim control (Fig. H on page 6). Remove the screwdriver and

gently

turn the trim control counterclockwise until the AF peak

indicator is illuminated only on audio peaks.

Return the screwdriver to its clip and close and secure the lower

body. No further transmitter gain adjustments should

be needed, as long as the acoustic input does not change

significantly.

ower/Mute/

attery Indicator

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Audio Technica ATW-701P Specifications Page 5

Comments to this Manuals

Related products and manuals for Recording Equipment Audio Technica ATW-701P