Audio Technica System 10 PRO Technical Information download pdf (Page 3)

System 10 Stompbox Installation and Operation

for interference-free communication. Time Diversity sends the signal

in multiple time slots to maximize immunity to multipath interference.

Finally, Space Diversity uses two antennas on each transmitter and

receiver to maximize signal integrity.

Each System 10 Stompbox professional digital wireless system

includes an ATW-R1500 Stompbox receiver, an ATW-T1001 UniPak

body-pack transmitter with an AT-GcW guitar cable, and hook &

loop strips for adding receiver to an effects pedal board. All A-T

Wireless Essentials

microphones and cables, available separately,

are pre-terminated for use with any ATW-T1001 transmitters. Note:

ATW-T1001 transmitters from earlier System 10 models may not be

compatible with the multi-transmitter pairing and battery level indicator

functions of the System 10 Stompbox receiver. However, these older

transmitter models may be shipped to the Audio-Technica Service

Department for ﬁrmware updates.

The ATW-R1500 receiver includes a switching power supply that

automatically adapts to changes in mains voltage.

The versatile ATW-T1001 UniPak body-pack transmitter has both

a high-impedance input for instruments, and a low-impedance input

with bias connection for use with dynamic and electret condenser

microphones.

The transmitter uses internal AA batteries and has a Power/Mute

switch and input Trim (level) adjustment.

Receiver Installation

Location

For best operation, the receiver should be at least 3' (1 m) away from

a wall or metal surface to minimize reﬂections. Keep the receiver away

from noise sources such as other digital equipment, microwave ovens,

as well as away from large metal objects. Keep System 10 Stompbox

receiver 30' (9 m) away from wireless access points. Operating

transmitters should be kept at least 3' (1 m) from receiver, but will

continue to work up to 60' (18 m) from receiver line of sight.

Output Connection

There are two switched TRS balanced ¼" output jacks on the side

panel. Either output can be connected to a guitar amp, a tuner or an

effects pedal.

Power Connection

Connect the DC plug on the included AC power adapter to the DC

power input on the back of the receiver. Then plug the adapter into

a standard 120 Volt 60 Hz or 230 Volt 50 Hz (depending on global

location) AC power outlet. The receiver may also be used in conjunction

with an effects pedal board with a common power supply, but each

output must be “isolated” in order to prevent noise interference.

(Note that the receiver has no power Off/On switch. The receiver will

be energized whenever the power adapter is connected and plugged

into the AC outlet. Unplug the power supply from the AC outlet when

the system is not in use — both for safety, and to conserve energy.)

ATW-R1500 Receiver Controls and Functions

Figure A — Top Panel Controls and Functions

1. Audio Output B: Switched TRS balanced ¼" phone jack.

Can be connected to guitar amp, tuner or effects

pedal input.

2. Audio Output A: Switched TRS balanced ¼" phone jack. Can be

connected to guitar amp, tuner or effects pedal input.

3. A/B Output Indicators: Glows green if output is on, glows red

if output is off or muted.

4. System ID Select Switch: Press to cycle through System ID

numbers or to clear pairing. (System ID is an identical number

assigned to a paired receiver and transmitter for identiﬁcation

purposes.)

5. Pairing Switch: Press and hold to initiate or clear pairing.

6. System ID Display: Shows System ID number.

7. Foot Switch: Press to toggle between outputs.

8. AF Peak Indicator: Only lights when audio distortion is present

at maximum input.

9. Pair Indicator: Glows green to indicate presence of paired

transmitter. Also blinks green to indicate pairing mode activated.

10. Transmitter Battery Power Indicator

Figure B — Rear Panel Controls and Functions

1. Output Mode Selector: Use to switch between A or B Mode

and A Mute Mode.

2. Power Input Jack: Universal (center + or -) 9V-12V DC input.

Connect the DC plug from the included AC adapter.

54 6

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Audio Technica System 10 PRO Technical Information Page 3

Comments to this Manuals

Related products and manuals for Guitar accessories Audio Technica System 10 PRO